Search found 89 matches

by Flat_Rate
Tue Oct 30, 2018 7:17 am
Forum: Elite Software Programmer (ESP)
Topic: Smoother Decel - A solution.
Replies: 8
Views: 1006

Re: Smoother Decel - A solution.

Throttle follower?? Anyone care to explain this a little i havent seen anything mentioning that in the software
by Flat_Rate
Mon Oct 22, 2018 3:50 am
Forum: Elite Series
Topic: Testing outputs
Replies: 16
Views: 3882

Re: Testing outputs

Asks for it daily... 3 years later still none.. impressive
by Flat_Rate
Wed Aug 22, 2018 12:34 pm
Forum: Elite Series
Topic: How to correctly setup the ecu to run e85
Replies: 4
Views: 589

Re: How to correctly setup the ecu to run e85

i mapped the main fuel map in 4D... seems to work well
by Flat_Rate
Sun Jan 14, 2018 11:42 am
Forum: Elite Series
Topic: Elite 2500 ECU Fuse keeps blowing
Replies: 4
Views: 576

Re: Elite 2500 ECU Fuse keeps blowing

looking at the diagram the red/white wire feeds the Circuit, it is fused at the battery and that fuse does not blow.. so its something on the ECU side. According to Haltechs Diagram it only feeds the Grey/red wires for sensors/solenoids and also powers ECU. I have disconnected everything from the 12...
by Flat_Rate
Sun Jan 14, 2018 2:09 am
Forum: Elite Series
Topic: Elite 2500 ECU Fuse keeps blowing
Replies: 4
Views: 576

Re: Elite 2500 ECU Fuse keeps blowing

If that feed wire was shorted it would be melted.. that doesn't make sense to me.
by Flat_Rate
Sat Jan 13, 2018 12:13 pm
Forum: Elite Series
Topic: Elite 2500 ECU Fuse keeps blowing
Replies: 4
Views: 576

Elite 2500 ECU Fuse keeps blowing

Im running Haltechs Preminum harness, car is an RB30 powered 240sx. I Was just driving along like normal and all of a sudden car died.. Found ECU fuse blown, replaced started and ran for another couple mins, died again with another blown fuse. Now Everytime i turn the ignition to the on position the...
by Flat_Rate
Sat Jan 13, 2018 7:23 am
Forum: Elite Series
Topic: LS3 with no timing marks, TDC offset angle
Replies: 6
Views: 917

Re: LS3 with no timing marks, TDC offset angle

How is using a piston stop tool and a degree wheel not accurate enough?
by Flat_Rate
Thu Dec 21, 2017 2:25 am
Forum: Elite Software Programmer (ESP)
Topic: Low PW Compensation
Replies: 14
Views: 3644

Re: Low PW Compensation

Excuse the noob question, but what is the difference between low pulse width compensation and the dead time table??
by Flat_Rate
Mon Dec 18, 2017 7:40 pm
Forum: Elite Series
Topic: Testing outputs
Replies: 16
Views: 3882

Re: Testing outputs

And the scope?!!
by Flat_Rate
Mon Dec 18, 2017 7:36 pm
Forum: Elite Software Programmer (ESP)
Topic: Flex Fuel Sampling Threshold
Replies: 5
Views: 1414

Re: Flex Fuel Sampling Threshold

Wouldn't the sensor pose a restriction on the feed side? It's only like -6 Isn't it. I suppose on lower power setup it'd be ok.
by Flat_Rate
Tue Dec 12, 2017 10:31 am
Forum: Elite Software Programmer (ESP)
Topic: Flex Fuel Sampling Threshold
Replies: 5
Views: 1414

Re: Flex Fuel Sampling Threshold

Defintaly something to watch for, when i was on the dyno starting to approach the limits of my fuel pumps the sensor was starting to read content erraticly (due to the lack of fuel being returned) which was throwing everything off. So good to datalog that sensor during pulls to make sure its on the ...
by Flat_Rate
Sat Dec 02, 2017 2:34 am
Forum: Elite Software Programmer (ESP)
Topic: SPI input KOEO
Replies: 2
Views: 931

Re: SPI input KOEO

Of course its off the ground lol i can see the speed output, but no raw data from the other SP1 channels.
by Flat_Rate
Fri Dec 01, 2017 11:30 am
Forum: Elite Software Programmer (ESP)
Topic: SPI input KOEO
Replies: 2
Views: 931

SPI input KOEO

Is there a way to see live data while the Engine is not running? Wanted to see VSS inputs without having to drive around..
by Flat_Rate
Mon Nov 06, 2017 10:55 pm
Forum: Elite Software Programmer (ESP)
Topic: Webinars for ESP functions
Replies: 8
Views: 1805

Re: Webinars for ESP functions

I have watched nearly all the Technically Speaking videos, and I look forward to new ones being released. I do agree that the information contained in them is somewhat generic. Tech support is excellent over the phone, but more detailed videos could likely reduce the need to tie your support staff ...
by Flat_Rate
Thu Jun 29, 2017 12:24 am
Forum: Elite Software Programmer (ESP)
Topic: Software Bug in 2.22 and 2.23??
Replies: 6
Views: 2517

Re: Software Bug in 2.22 and 2.23??

Ill try that, i didnt have anything checked on in the oil pressure Diagnostics tab so i figured it wouldnt throw a DTC. Thanks for the reply.

Go to advanced search