Search found 2435 matches

by HaltechMatthew
Fri Oct 19, 2018 9:11 am
Forum: Elite Series
Topic: NZ Wiring CAM Trigger (Bosch Reluctor) for RB25 Setup Issue
Replies: 4
Views: 17

Re: NZ Wiring CAM Trigger (Bosch Reluctor) for RB25 Setup Issue

If you are not getting a trigger tooth count then the ECU is not seeing the signal from the sensor. Being reluctor you should have used the Yellow Trigger + wire and the Green Trigger - wire from our loom. You maybe have the tooth gap too large, or the voltages set too high in the Trigger Arming Tab...
by HaltechMatthew
Thu Oct 18, 2018 12:40 pm
Forum: Elite Series
Topic: Signal ground has continuity with Chassis ground when ECU plugged in.
Replies: 5
Views: 365

Re: Signal ground has continuity with Chassis ground when ECU plugged in.

You have something very certainly screwed up if you can melt the USB cable just by trying to going online. I cant even think how it is possible!
by HaltechMatthew
Thu Oct 18, 2018 12:35 pm
Forum: Elite Series
Topic: Elite 950 GM 4 wire IAC help
Replies: 5
Views: 159

Re: Elite 950 GM 4 wire IAC help

We do. Its called an Elite 1000/1500/2000/2500 :D

These all support stepper motors. Single connector ECUs do not. We can add it but it makes it more expensive and you need more ECU pins, so you pretty much end up with the higher spec ECU anyway.
by HaltechMatthew
Thu Oct 18, 2018 12:30 pm
Forum: Elite Software Programmer (ESP)
Topic: Bugs/requests for ESP/Hardware
Replies: 1
Views: 549

Re: Bugs/requests for ESP/Hardware

The short answer why there is not a plug in is that the demand has been very low, the development time high, and other larger projects have stolen that available time. Nothing personal, just the way it goes with the resources available.
by HaltechMatthew
Thu Oct 18, 2018 12:19 pm
Forum: Elite Series
Topic: Elite 2500 + RX7 (Series 6, twin turbo) PNP
Replies: 3
Views: 107

Re: Elite 2500 + RX7 (Series 6, twin turbo) PNP

Monitor the OMP Position, tell the map to go to a position, does it move there. If it does then it works. :D
by HaltechMatthew
Thu Oct 18, 2018 12:04 pm
Forum: Elite Series
Topic: batch fire question?
Replies: 3
Views: 33

Re: batch fire question?

As soon as you are not injecting sequentially it makes no difference how the injectors are wired. In Batch Fire it does not have a sequencing reference anyway so it can start firing at any time in the cycle so it is never the exact same each time you start the engine. Firing it more than once per cy...
by HaltechMatthew
Mon Oct 15, 2018 1:27 pm
Forum: Elite Series
Topic: DBW Cruise Control
Replies: 25
Views: 9012

Re: DBW Cruise Control

Coming shortly.
by HaltechMatthew
Mon Oct 15, 2018 1:27 pm
Forum: Elite Series
Topic: SR20 optical CAS
Replies: 2
Views: 63

Re: SR20 optical CAS

Pick a trigger type that has this same trigger. Toyota 4AG or 2JZ non-vvt
by HaltechMatthew
Mon Oct 15, 2018 1:12 pm
Forum: Elite Series
Topic: Stumbling & Hesitation after Idling or Cruising
Replies: 2
Views: 61

Re: Stumbling & Hesitation after Idling or Cruising

Map and logs my friend
by HaltechMatthew
Mon Oct 15, 2018 12:56 pm
Forum: Elite Series
Topic: 10 Amp mini relay for EMS?
Replies: 1
Views: 53

Re: 10 Amp mini relay for EMS?

The ECU does not draw much current, so 10A should cover it.
by HaltechMatthew
Mon Oct 15, 2018 12:54 pm
Forum: Elite Series
Topic: Dual DBW Throttles?
Replies: 1
Views: 40

Re: Dual DBW Throttles?

We do not support dual DBW throttle control.
by HaltechMatthew
Wed Sep 19, 2018 4:57 pm
Forum: Elite Software Programmer (ESP)
Topic: Possible bug in 2.27.1 - Ignition only idle control
Replies: 4
Views: 265

Re: Possible bug in 2.27.1 - Ignition only idle control

Tested it on the bench and works as it should. Keep an eye on your Decel Min RPM table. It should not be doing any idle control if you are above this RPM. The table does the decel fuel cut but also holds off idle control from chasing ghosts under deceleration at higher RPM. It also prevents O2 Contr...
by HaltechMatthew
Wed Sep 19, 2018 4:46 pm
Forum: Elite Software Programmer (ESP)
Topic: ESP software will not open at all.
Replies: 2
Views: 136

Re: ESP software will not open at all.

The issues usually relate to not having DirectX9 installed or not having the early .NET installed. Some iterations of Win 10 block the installer from putting the files where it is needed and running the installer as Administrator can sometimes overcome this. Security seems to sometimes block the wri...
by HaltechMatthew
Fri Sep 14, 2018 12:32 pm
Forum: Elite Series
Topic: elite 2500 and racepack iq3 street
Replies: 2
Views: 355

Re: elite 2500 and racepack iq3 street

Plug the dash directly into the ECU to see if it communicates.
by HaltechMatthew
Fri Sep 14, 2018 12:28 pm
Forum: Elite Series
Topic: New 2.27 Firmware / 2.00.32 Software Release
Replies: 4
Views: 475

Re: New 2.27 Firmware / 2.00.32 Software Release

Many updates there but my personal favourite in 2.27 is the throttle follower. Smooths the transition from open to closed throttle using the idle control system.

Go to advanced search