Search found 2037 matches

by HaltechMatthew
Fri Aug 18, 2017 4:34 pm
Forum: Elite Series
Topic: Is the 750 capable of high boost and low boost map?
Replies: 1
Views: 15

Re: Is the 750 capable of high boost and low boost map?

The 550 and 750 were actually expanded in the last firmware to allow 32x16 to better support the rpm range of the typical motorbike engine. There is a single table and it does not support the 4D level of tuning that you can do with the E1500/2500 models For changes in boost pressure you would not no...
by HaltechMatthew
Fri Aug 18, 2017 11:03 am
Forum: Elite Series
Topic: Synchronised pulsed input
Replies: 1
Views: 22

Re: Synchronised pulsed input

Yes, just use an external 1k pullup as the internal one is not the same as used for AVI's. Using the internal pullup will cause any calibration to read off.
by HaltechMatthew
Fri Aug 18, 2017 11:02 am
Forum: Elite Series
Topic: Elite 2500 throwing ECU Overtemp
Replies: 8
Views: 756

Re: Elite 2500 throwing ECU Overtemp

Injector outputs are better suited to cam solenoids. 99% of the time any output is fine, but if it is drawing a particularly large amount of current it could be cooking the driver.
by HaltechMatthew
Wed Aug 16, 2017 12:38 pm
Forum: E6X/E6GMX/F10X
Topic: Cold Start - hard to start and Not revving up
Replies: 2
Views: 39

Re: Cold Start - hard to start and Not revving up

It could be anything. Check if the throttle is calibrated and reads 0% at idle. If it doesnt the idle control will not work and wont idle up when cold.
by HaltechMatthew
Wed Aug 16, 2017 12:33 pm
Forum: Platinum Pro Plug-in
Topic: Z33 EVAP Control Settings?
Replies: 4
Views: 39

Re: Z33 EVAP Control Settings?

Yes your equation is correct.
by HaltechMatthew
Wed Aug 16, 2017 12:31 pm
Forum: Elite Series
Topic: Wiring Elite 2500 Terminated LS3 Harness
Replies: 2
Views: 35

Re: Wiring Elite 2500 Terminated LS3 Harness

The battery is always the best place to run the wires as it acts like a large filter.
by HaltechMatthew
Wed Aug 16, 2017 12:29 pm
Forum: Elite Series
Topic: Elite 550 Toyota 4AGE 16V Dizzy wiring
Replies: 9
Views: 347

Re: Elite 550 Toyota 4AGE 16V Dizzy wiring

Correct. 11,31,32
by HaltechMatthew
Tue Aug 15, 2017 1:16 pm
Forum: E6X/E6GMX/F10X
Topic: E6x to run a ls1 motor
Replies: 1
Views: 53

Re: E6x to run a ls1 motor

Just NO! Do not use an E6X to run an LS.
by HaltechMatthew
Tue Aug 15, 2017 1:15 pm
Forum: Platinum Sprint Series
Topic: Cold start extra air valve
Replies: 1
Views: 77

Re: Cold start extra air valve

Your Sprint ECU does not support stepper motor, the Sport and high Elite models do.

You would have to use a 2-pin idle motor like the Bosch unit.
by HaltechMatthew
Tue Aug 15, 2017 1:12 pm
Forum: Platinum Pro Plug-in
Topic: adding a innovate MXTL to haltech
Replies: 2
Views: 62

Re: adding a innovate MXTL to haltech

Connect your 0-5V output to a spare AVI.
by HaltechMatthew
Tue Aug 15, 2017 1:11 pm
Forum: Platinum Pro Plug-in
Topic: Z33 EVAP Control Settings?
Replies: 4
Views: 39

Re: Z33 EVAP Control Settings?

0% means no correction. Not zero output.
by HaltechMatthew
Tue Aug 15, 2017 1:10 pm
Forum: Platinum Pro Plug-in
Topic: GFB boost controller installed to haltech
Replies: 1
Views: 42

Re: GFB boost controller installed to haltech

Yes, wire the solenoid to the Haltech instead of the current controller.
by HaltechMatthew
Tue Aug 15, 2017 1:01 pm
Forum: Elite Series
Topic: problem in running DBW
Replies: 2
Views: 80

Re: problem in running DBW

That just says the throttle is disabled. You need to supply much more information than this to be able to help. Nobody though is going to be able to diagnose a DBW fault over a forum. Call Support.

Go to advanced search