Search found 2040 matches

by HaltechMatthew
Mon Aug 21, 2017 1:08 pm
Forum: Platinum Sport Series
Topic: PS100 & WBC2 coms fault
Replies: 2
Views: 16

Re: PS100 & WBC2 coms fault

you must use v1.13 software and firmware.
by HaltechMatthew
Mon Aug 21, 2017 1:02 pm
Forum: Elite Series
Topic: Wheel speed with Variable Reluctance abs sensors for traction control on Elite 2500
Replies: 1
Views: 14

Re: Wheel speed with Variable Reluctance abs sensors for traction control on Elite 2500

It can read most sensors but you would need to scope the sensor and show me the waveform to know if it will work. Many are 2-pin Hall Effect.
by HaltechMatthew
Fri Aug 18, 2017 4:34 pm
Forum: Elite Series
Topic: Is the 750 capable of high boost and low boost map?
Replies: 2
Views: 36

Re: Is the 750 capable of high boost and low boost map?

The 550 and 750 were actually expanded in the last firmware to allow 32x16 to better support the rpm range of the typical motorbike engine. There is a single table and it does not support the 4D level of tuning that you can do with the E1500/2500 models For changes in boost pressure you would not no...
by HaltechMatthew
Fri Aug 18, 2017 11:03 am
Forum: Elite Series
Topic: Synchronised pulsed input
Replies: 1
Views: 38

Re: Synchronised pulsed input

Yes, just use an external 1k pullup as the internal one is not the same as used for AVI's. Using the internal pullup will cause any calibration to read off.
by HaltechMatthew
Fri Aug 18, 2017 11:02 am
Forum: Elite Series
Topic: Elite 2500 throwing ECU Overtemp
Replies: 8
Views: 778

Re: Elite 2500 throwing ECU Overtemp

Injector outputs are better suited to cam solenoids. 99% of the time any output is fine, but if it is drawing a particularly large amount of current it could be cooking the driver.
by HaltechMatthew
Wed Aug 16, 2017 12:38 pm
Forum: E6X/E6GMX/F10X
Topic: Cold Start - hard to start and Not revving up
Replies: 2
Views: 52

Re: Cold Start - hard to start and Not revving up

It could be anything. Check if the throttle is calibrated and reads 0% at idle. If it doesnt the idle control will not work and wont idle up when cold.
by HaltechMatthew
Wed Aug 16, 2017 12:33 pm
Forum: Platinum Pro Plug-in
Topic: Z33 EVAP Control Settings?
Replies: 4
Views: 50

Re: Z33 EVAP Control Settings?

Yes your equation is correct.
by HaltechMatthew
Wed Aug 16, 2017 12:31 pm
Forum: Elite Series
Topic: Wiring Elite 2500 Terminated LS3 Harness
Replies: 2
Views: 49

Re: Wiring Elite 2500 Terminated LS3 Harness

The battery is always the best place to run the wires as it acts like a large filter.
by HaltechMatthew
Wed Aug 16, 2017 12:29 pm
Forum: Elite Series
Topic: Elite 550 Toyota 4AGE 16V Dizzy wiring
Replies: 9
Views: 358

Re: Elite 550 Toyota 4AGE 16V Dizzy wiring

Correct. 11,31,32
by HaltechMatthew
Tue Aug 15, 2017 1:16 pm
Forum: E6X/E6GMX/F10X
Topic: E6x to run a ls1 motor
Replies: 1
Views: 60

Re: E6x to run a ls1 motor

Just NO! Do not use an E6X to run an LS.
by HaltechMatthew
Tue Aug 15, 2017 1:15 pm
Forum: Platinum Sprint Series
Topic: Cold start extra air valve
Replies: 1
Views: 84

Re: Cold start extra air valve

Your Sprint ECU does not support stepper motor, the Sport and high Elite models do.

You would have to use a 2-pin idle motor like the Bosch unit.
by HaltechMatthew
Tue Aug 15, 2017 1:12 pm
Forum: Platinum Pro Plug-in
Topic: adding a innovate MXTL to haltech
Replies: 3
Views: 68

Re: adding a innovate MXTL to haltech

Connect your 0-5V output to a spare AVI.
by HaltechMatthew
Tue Aug 15, 2017 1:11 pm
Forum: Platinum Pro Plug-in
Topic: Z33 EVAP Control Settings?
Replies: 4
Views: 50

Re: Z33 EVAP Control Settings?

0% means no correction. Not zero output.

Go to advanced search