Search found 12 matches

by aussie_guy00000
Sat May 05, 2018 9:34 pm
Forum: Elite Series
Topic: 5V supply for I/O Canbus module
Replies: 0
Views: 226

5V supply for I/O Canbus module

Hey Guys, i'm fitting an I/O canbus module to my elite 1500, and I know you need to connect the signal ground to the ECU signal ground, but I wanted to check if I there'll be any issues using the 5V supply from the ECU for the sensors going to the I/O module, instead of the 5V supply from the I/O mo...
by aussie_guy00000
Mon Nov 16, 2015 9:09 pm
Forum: Feature Requests
Topic: Cruise control
Replies: 2
Views: 4062

Cruise control

I would like to request the ability to add cruise control to my DBW equipped elite ECU'd vehicle, I lost cruise control when I installed the ECU due to the cruise control being run by the factory ecu, so just need the application code written to enable a series of inputs to interface with the factor...
by aussie_guy00000
Mon Nov 16, 2015 8:03 pm
Forum: Elite Software Programmer (ESP)
Topic: Launch control will not activate?
Replies: 20
Views: 5684

Re: Launch control will not activate?

I have the same issue with my 1500. I tried directly earthing a spare input (AVI10) and trying always on, but so far have had no luck being able to activate it.
by aussie_guy00000
Sat Nov 07, 2015 9:39 am
Forum: Elite Series
Topic: Wide Band sensor LSU 4.2 vs 4.9
Replies: 2
Views: 1314

Re: Wide Band sensor LSU 4.2 vs 4.9

Thanks Matt.
by aussie_guy00000
Sun Nov 01, 2015 2:55 pm
Forum: Elite Series
Topic: Wide Band sensor LSU 4.2 vs 4.9
Replies: 2
Views: 1314

Wide Band sensor LSU 4.2 vs 4.9

Hi Guys, I have a MY06 STI that i've recently installed an Elite 1500 and a WBC1 Wideband controller in. All was going well into I accidently ran over a Roo carcass (I live in Central QLD) and it destroyed the Bosch LSU 4.2 O2 sensor in the exhaust under the car. I have a spare Bosch LSU 4.9 sensor ...
by aussie_guy00000
Thu Aug 20, 2015 8:29 pm
Forum: Elite Series
Topic: SUBARU EJ257 08+ dual avcs DWB throttle - POSSIBLE?
Replies: 3
Views: 1696

Re: SUBARU EJ257 08+ dual avcs DWB throttle - POSSIBLE?

Definitely possible, have a look through this build log. There's a whole series of videos on you tube for the build too. http://mightycarmods.com/blogs/news/15440417-martys-gramps-build-diary-in-pictures The engine they used is an EZ36 subaru engine, however it has DBW and AVCS on all 4x cams. I jus...
by aussie_guy00000
Sun Aug 09, 2015 8:44 am
Forum: Elite Series
Topic: Elite 1500 wrx gd coil on plug
Replies: 2
Views: 1063

Re: Elite 1500 wrx gd coil on plug

Even without knowing that, one is earth (pretty sure it's earthed through the ECU using a common to all coils wire), one is an ignition switched 12v supply, and the last is a smaller wire which is the trigger direct from the ECU pinouts. Pretty easy to identify which is which looking, or at least us...
by aussie_guy00000
Sun Aug 09, 2015 8:37 am
Forum: Elite Series
Topic: Elite 1500 wrx gd coil on plug
Replies: 2
Views: 1063

Re: Elite 1500 wrx gd coil on plug

What year and model do you have?
by aussie_guy00000
Sun May 10, 2015 11:06 am
Forum: Elite Software Programmer (ESP)
Topic: Selecting Elite 1500 in ESP software
Replies: 8
Views: 2254

Re: Selecting Elite 1500 in ESP software

That was just the issue Matt, when I created a new file, the only option was the 2500, there was no 1500 option. I've sorted it, but I had to power up the ecu and download the base map off it to get a starting 1500 map, there was no way I could create a new one from scratch.
by aussie_guy00000
Sun Mar 22, 2015 12:32 pm
Forum: Elite Software Programmer (ESP)
Topic: Selecting Elite 1500 in ESP software
Replies: 8
Views: 2254

Re: Selecting Elite 1500 in ESP software

You're a legend Jim, that did the trick. I downloaded the base map from the ECU and then imported the Base map that Haltech had sent me for my car with a 2500 elite.

Again however, would have been a heap easier if I could have just selected the ECU type
by aussie_guy00000
Sat Mar 21, 2015 11:15 am
Forum: Elite Software Programmer (ESP)
Topic: Selecting Elite 1500 in ESP software
Replies: 8
Views: 2254

Re: Selecting Elite 1500 in ESP software

The main issue I have is that I been sent a base map for my car, but it's the 2500 version, and I can't find where one would change the version. I can't find any reference to the 1500 version anywhere in the help file or menus. I have manually reconfigured the I/O's to not include Inj 5-8 & Ign ...
by aussie_guy00000
Thu Mar 19, 2015 8:59 pm
Forum: Elite Software Programmer (ESP)
Topic: Selecting Elite 1500 in ESP software
Replies: 8
Views: 2254

Selecting Elite 1500 in ESP software

I just bought myself a Haltech 1500 ECU and i'm at the stage of setting up the pin outs before I get stuck into wiring it. I cannot however select the 1500 when creating a new map, it only has the 2500 option. I'm told by the gentleman at Haltech i've been dealing with that I should be able to selec...

Go to advanced search