Search found 9 matches

by RWPracing
Sat Sep 30, 2017 10:07 pm
Forum: ECU Manager
Topic: Axis setup
Replies: 1
Views: 247

Axis setup

Using a Ps2000
Why I limited to a max value of 8000rpm and 29psi when entering values in table setup? by default the rpm already has 9000 and 10000 cells. Is there any way around this or just what I am stuck with?
by RWPracing
Mon Mar 06, 2017 11:12 am
Forum: Platinum Sport Series
Topic: PS 1000 showing idle in neutral with 8 psi boost
Replies: 7
Views: 868

Re: PS 1000 showing idle in neutral with 8 psi boost

How are you reading the manifold pressure? the internal sensor or a map sensor?
by RWPracing
Mon Mar 06, 2017 11:10 am
Forum: Platinum Sport Series
Topic: How do I hook up a Bosch 4.9 wideband o2 to the ps2000?
Replies: 4
Views: 683

Re: How do I hook up a Bosch 4.9 wideband o2 to the ps2000?

Yeah you need to convert the sensor out put to a 0 to 5v signal then you can set the calibration up. Or you could just use the haltech wideband.
by RWPracing
Mon Mar 06, 2017 8:56 am
Forum: Platinum Sport Series
Topic: Anti lag with transbrake
Replies: 1
Views: 473

Anti lag with transbrake

Is it able to use the anti lag launch function with a transbrake. I have ignition set at 20 degrees and when it goes into the cut mode it seems the load on the engine drags the rpm down. So never reaches the hard cut.
by RWPracing
Wed Mar 30, 2016 6:30 pm
Forum: Platinum Sport Series
Topic: CAN info to racepak
Replies: 5
Views: 775

Re: CAN info to racepak

When i have it set up as afr because its methanol 6.4 is stoic instead of 14.7 for petrol. so my 0-5v input for wideband is calibrated for methanol. when it is reading open air the afr is the same on the racepak as the value displayed in the ecu software. But with the engine running the afr is aroun...
by RWPracing
Mon Mar 28, 2016 10:07 am
Forum: Platinum Sport Series
Topic: CAN info to racepak
Replies: 5
Views: 775

Re: CAN info to racepak

Ok had a play around and if i change to using lambda on my calibration table in the ecu software and have 1 = 0.0064 it reads correctly on the racepak. But now i don't have afr in ecu. Is there a setting i can change so it can change the sat afr ratio
by RWPracing
Sat Mar 26, 2016 11:42 am
Forum: Platinum Sport Series
Topic: CAN info to racepak
Replies: 5
Views: 775

Re: CAN info to racepak

Tried that with the sensors disconnected its reading 5.8 on ecu and 3.0 on racepak
by RWPracing
Wed Mar 23, 2016 4:28 pm
Forum: Platinum Sport Series
Topic: CAN info to racepak
Replies: 5
Views: 775

CAN info to racepak

Hey guys so I am running methanol on my engine and using a wideband that uses a 0-5v signal to ecu. I can see the correct values on the ecu but on the racpak that's connected by can the values wont read below 7. Are showing the same as ecu when in open air. What settings do I need to change to read ...
by RWPracing
Sat Mar 05, 2016 5:12 pm
Forum: Platinum Sport Series
Topic: Indy Blue Dead times
Replies: 1
Views: 694

Indy Blue Dead times

Hey guys
Do you know the dead times for bosh indy blue 1680cc injector?

Go to advanced search