Search found 17 matches

by TRD-021
Tue Aug 01, 2017 8:33 pm
Forum: Elite Series
Topic: Motor dies after reving up
Replies: 7
Views: 468

Re: Motor dies after reving up

How is the fuel pump wired?
Did you wired the fuel pump directly to the ecu?
by TRD-021
Mon Jun 19, 2017 1:10 pm
Forum: Elite Software Programmer (ESP)
Topic: ST215 Gen 4 Setup
Replies: 15
Views: 3476

Re: ST215 Gen 4 Setup

The can confirm the trigger configuration for the st246 is the same as the st215. I have the manual for a st246 and it helped me a lot with the wiring and set up for my st215 engine. The only difference that I know is that the st215 has a side mounted intake manifold and the st246 has a centred inta...
by TRD-021
Tue May 09, 2017 9:56 am
Forum: Elite Series
Topic: ST215 Gen 4 Setup
Replies: 6
Views: 1213

Re: ST215 Gen 4 Setup

Sorry, I haven't been here for a while, yes I wire up the ignition wire (A13) into the old injector wires as my ignition source.
by TRD-021
Sat Apr 01, 2017 8:27 pm
Forum: Elite Series
Topic: ST215 Gen 4 Setup
Replies: 6
Views: 1213

Re: ST215 Gen 4 Setup

Hi Alex,

attached is my map.
by TRD-021
Sat Dec 03, 2016 4:43 pm
Forum: Elite Series
Topic: Elite Wiring O2 sensor
Replies: 3
Views: 1450

Re: Elite Wiring O2 sensor

thanks mate.
by TRD-021
Tue Nov 29, 2016 9:29 pm
Forum: Elite Series
Topic: Elite Wiring O2 sensor
Replies: 3
Views: 1450

Re: Elite Wiring O2 sensor

Has anyone installed a O2 sensor for an elite ECU?
by TRD-021
Mon Nov 28, 2016 8:42 am
Forum: Elite Series
Topic: Elite Wiring O2 sensor
Replies: 3
Views: 1450

Elite Wiring O2 sensor

Hi All, I'm wiring up my o2 sensor and I'm using AVI 1 which on the diagram it says its suitable for narrowband sensor, I've noticed its bundle up with a tag that reads "O2 input #1" and it has 3 wires, grey/orange (shield), black/white (ground) and a grey/red, the grey/red wire when the k...
by TRD-021
Fri Nov 25, 2016 6:52 am
Forum: Elite Series
Topic: Elite2500 in 2jzgte mkiv Supra
Replies: 6
Views: 2726

Re: Elite2500 in 2jzgte mkiv Supra

Splice the wires.
by TRD-021
Sun Nov 06, 2016 9:46 am
Forum: Elite Series
Topic: ST215 Gen 4 Setup
Replies: 6
Views: 1213

Re: ST215 Gen 4 Setup

the engine is freshly rebuilt with all forge goodies.

its all sorted out it synchronised with 215 TDC offset angle and I've wired up the fuel pump directly from ecu. I think the time response of the relays aren't quick enough for the haltech :) the car is running now
by TRD-021
Sun Nov 06, 2016 9:40 am
Forum: Elite Software Programmer (ESP)
Topic: ST215 Gen 4 Setup
Replies: 15
Views: 3476

Re: ST215 Gen 4 Setup

got it synchronised, it turns out I had some wrong setting with the home. end up with totally different TDC angle.

I got the car started but i'll post this on the other section
by TRD-021
Sat Nov 05, 2016 5:39 pm
Forum: Elite Series
Topic: ST215 Gen 4 Setup
Replies: 6
Views: 1213

ST215 Gen 4 Setup

Hey all I've got a Grp A ST185 GT4 with a 3sgte ST215 gen IV and elite 1500, I've recently manage to start my car but it only stays on for 2 secs then it turns off. someone on FB suggested that it could be the pump cutting out, but I've bypass the circuit open relay (COR) and fuel pump control relay...
by TRD-021
Wed Oct 26, 2016 7:34 pm
Forum: Elite Software Programmer (ESP)
Topic: ST215 Gen 4 Setup
Replies: 15
Views: 3476

Re: ST215 Gen 4 Setup

Well I think I nearly there setting up the trigger.

I didn't get any errors
by TRD-021
Mon Oct 24, 2016 2:24 pm
Forum: Elite Software Programmer (ESP)
Topic: ST215 Gen 4 Setup
Replies: 15
Views: 3476

Re: ST215 Gen 4 Setup

Hi Matt, I think something wrong happened to that file. i'll try again later. 2 weeks ago I went to the Haltech shop in Wetherill Park and showed my map to one of the guys. i was using a very old version and old firm ware, he also gave me some tips on how to set the diagnostic page. I had some wirin...
by TRD-021
Sat Oct 01, 2016 9:36 pm
Forum: Elite Software Programmer (ESP)
Topic: ST215 Gen 4 Setup
Replies: 15
Views: 3476

Re: ST215 Gen 4 Setup

Hi Matt, I hope this works, I was getting an error message and I couldn't attached the map, so I've changed the extension file to pdf and it's allowing me to attached the map I manage to add some trigger angle and the car started for 2 seconds and them I got an code - engine position. I don't know i...
by TRD-021
Wed Sep 28, 2016 9:26 pm
Forum: Elite Software Programmer (ESP)
Topic: ST215 Gen 4 Setup
Replies: 15
Views: 3476

ST215 Gen 4 Setup

Hi All, i'm new to the aftermarket ecu world and trying to learn everything at once but I founding it a bit overwhelming. I have a Grp A ST185 with a freshly rebuilt ST215 gen 4 engine from a caldina, I just finished wiring up an elite 1500. everything is standard, well standard injectors, COP syste...

Go to advanced search