Search found 16 matches

by Datthor
Sun Aug 05, 2018 4:16 pm
Forum: Elite Series
Topic: Idle control settings and definitions
Replies: 1
Views: 264

Idle control settings and definitions

Looking to try and setup idle for Elite 1500 on SR20DET with Hypertune manifold and 77mm Throttle body.
Haltech supplied 2 wire BAC.

Can't find any info as to where to start. Definition for various setting within idle control settings.
by Datthor
Sun Jul 29, 2018 8:12 pm
Forum: Elite Series
Topic: Throttle body and IACV settings
Replies: 3
Views: 319

Re: Throttle body and IACV settings

Is there a general starting point for Hz setting.
I notice it is 300 Hz from standard.
Using the 2 wire Haltech valve.
by Datthor
Sun Jul 29, 2018 2:06 am
Forum: Elite Series
Topic: Throttle body and IACV settings
Replies: 3
Views: 319

Throttle body and IACV settings

Just fitted a Hypertune Throttle body to a SR20DET and also fitted a 2 wire Haltech IACV replacing old throttle body which hade stepper motor idle control. 2 questions. . With IACV blocked off do you adjust throttle body stopper to allow engine to idle. At the moment if you block IACV hose engine st...
by Datthor
Sat Jul 21, 2018 4:53 pm
Forum: Elite Series
Topic: Sr20det manual tps
Replies: 2
Views: 212

Re: Sr20det manual tps

Awesome post... thanks.
by Datthor
Wed Jul 18, 2018 6:18 pm
Forum: Elite Series
Topic: Sr20det manual tps
Replies: 2
Views: 212

Sr20det manual tps

Looking for wiring connection pinouts for Nissan sr20det s14 manual tps connector

0 volt
tps signal
5 volt
by Datthor
Wed Apr 25, 2018 9:35 pm
Forum: Elite Series
Topic: Multifunction Can gauge
Replies: 1
Views: 337

Multifunction Can gauge

Looking at the Haltech multifunction Can Gauge and just trying to figure out how to connect as i have a wide band module plugged into the can harness connector ...
Can i just "T" into the same can wiring?
by Datthor
Sat Apr 21, 2018 10:12 am
Forum: Elite Series
Topic: IACV for SR20det
Replies: 4
Views: 626

Re: IACV for SR20det

Thanks Peterson
by Datthor
Thu Apr 19, 2018 1:04 pm
Forum: Elite Series
Topic: Flat shift delay
Replies: 4
Views: 628

Re: Flat shift delay

Yep I got the blockout function sorted for the delay in reactivation, but just looking for ignition cut duration as a starting point..

Was looking at around 120 - 150ms?
by Datthor
Thu Apr 19, 2018 1:01 pm
Forum: Elite Series
Topic: IACV for SR20det
Replies: 4
Views: 626

Re: IACV for SR20det

I got the Bosch 2 wire IACV from Haltech and just looking at the plumbing
Noticed some plumb the incoming to intake pipe before the throttle body and others use a small filter to atmosphere instead.

Which is the best way?
by Datthor
Tue Apr 10, 2018 10:30 am
Forum: Elite Series
Topic: Flat shift delay
Replies: 4
Views: 628

Re: Flat shift delay

What sort of time is usually best starting point for flat shift time in the tables.. it is set to 500 ms as default.
This seems a bit long.

Running a RB25DET box with PPG dog set. Torque type gear knob as switch for H Pattern.
by Datthor
Tue Mar 13, 2018 11:30 am
Forum: Elite Series
Topic: Toyota coil packs
Replies: 1
Views: 428

Toyota coil packs

I bought some toyota coil packs off ebay 90919-02240 and had one fail has any one got a decent supplier for aftermarket coils besides Toyota.
by Datthor
Sat Mar 10, 2018 2:30 pm
Forum: Elite Series
Topic: Flat shift delay
Replies: 4
Views: 628

Flat shift delay

Just checking if there is some setting to help my flat shift. I have a h pattern dog box with a torque type gear knob for activation. The problem is that I have a tendency to keep pushing the gearstick forward on 2nd to 3rd shift change which causes the ecu to keep cutting fuel while switch is engag...
by Datthor
Tue Mar 06, 2018 6:57 pm
Forum: Elite Series
Topic: IACV for SR20det
Replies: 4
Views: 626

IACV for SR20det

Just checking which is the best IACV to use on a SR20det with hypertune intake.
Running Elite 1500
by Datthor
Thu Jun 30, 2016 11:36 pm
Forum: Elite Series
Topic: A26 battery or Ignition
Replies: 3
Views: 3018

Re: A26 battery or Ignition

The injectors are fed from a permanent battery feed not an ignition feed.

Does this matter as I could change the injector feed to switched ignition....
by Datthor
Tue Jun 07, 2016 2:19 pm
Forum: Elite Series
Topic: Elite 2500 - Grounding Pins
Replies: 7
Views: 4720

Re: Elite 2500 - Grounding Pins

Does this also apply to inputs that switch to ground.
For example I have AVI 2 (pin A16) switched to ground through a toggle switch with pull up enabled.

Go to advanced search