Search found 9 matches

by dawesy
Fri Sep 07, 2018 9:50 pm
Forum: Elite Series
Topic: Honda K20 Type R alternator connections to Elite 1500
Replies: 1
Views: 343

Re: Honda K20 Type R alternator connections to Elite 1500

i take it its a 4 wire regulator connection? if you have the terminals labeled on the alternator then this chart may help. http://www.autoelectro.co.uk/sites/default/files/media/docs/AERegulatorGuide.pdf worth noting that the monitor terminal doesnt need connecting when running a stand alone as its ...
by dawesy
Tue Aug 28, 2018 6:54 pm
Forum: Off-Topic
Topic: Id like to try for a sponsorship.
Replies: 2
Views: 358

Re: Id like to try for a sponsorship.

There’s a sponsorship tab on the main Haltech page under contact I believe.
by dawesy
Sat Aug 25, 2018 12:36 am
Forum: Elite Series
Topic: Issue with spi on cam sensors
Replies: 2
Views: 288

Re: Issue with spi on cam sensors

Thanks mathew.
all sorted now. ive ended up with a 4Kohm pull up on them now and all working fine.
why the home sensor needs a 550ohm internal im not sure as all sensors are the same.
thanks for your continued support :D
by dawesy
Thu Aug 09, 2018 11:16 pm
Forum: Elite Series
Topic: Issue with spi on cam sensors
Replies: 2
Views: 288

Issue with spi on cam sensors

Looking for help. Toyota 2GR-FE on Haltech Elite 2500. Got the CAS working fine on intake bank 1 (home position sensor) using strong pull up (internal 550ohm resistor) and 5V feed. Can’t get the other sensors to sync. All CAS are the same sensors all wired up and tested ok and all swapped with inlet...
by dawesy
Fri Jun 29, 2018 7:18 pm
Forum: Elite Series
Topic: Toyota 2GR-FE CAS settings
Replies: 0
Views: 215

Toyota 2GR-FE CAS settings

Hoping someone here can help. I’m fitting a Haltech Elite 2500 to a 2GR V6. It’s all wired up and will run but I’m not getting a home signal. Wiring has been checked and is good. I called the Kentucky office yesterday and the guy said that the 2GR CAS needs custom selected in type due to the output ...
by dawesy
Fri May 18, 2018 11:36 pm
Forum: Elite Series
Topic: Screened single core wire for elite 2500 harnes.
Replies: 1
Views: 277

Screened single core wire for elite 2500 harnes.

Where can I by the screened single core wire that is in the elite basic harness? (Spi, knock etc)
Haltech do a 4cyl wire kit but I have the other wires already and just need the screened cable.
Any help or sources greatly appreciated
by dawesy
Tue Aug 22, 2017 9:10 pm
Forum: Elite Series
Topic: Synchronised pulsed input
Replies: 4
Views: 953

Re: Synchronised pulsed input

Excellent. Thanks for the info :D
by dawesy
Thu Aug 17, 2017 7:25 pm
Forum: Elite Series
Topic: Synchronised pulsed input
Replies: 4
Views: 953

Synchronised pulsed input

Can I use one of these for an engine bay temp sensor?
I have an elite 2500 on an MR2 with DBW and direct fire ignition and I've run out of other inputs.
I want to use the sensor to control an engine bay cooling fan.
by dawesy
Thu Jun 01, 2017 4:12 am
Forum: Elite Series
Topic: DBW set up and calibration
Replies: 2
Views: 780

DBW set up and calibration

Is there a Technically speaking video for DBW set up and calibration?
not actualy got that far in the installation yet but would like some tips for when i do.
it looks fairly straight forward from what i can see but dont want to miss something important.

Go to advanced search