Dreamer??

T Kilby
Posts: 6
Joined: Mon Sep 21, 2009 8:16 pm

Dreamer??

Postby T Kilby » Tue Oct 20, 2009 8:18 pm

Does anybody know if it would actually be possible to run a fuel injected enduro/MX bike on a E6X? The question comes from the thought/dream of building a turbo 450 or maybe 510 bike, sorta pointless but novel none the less. :D

User avatar
Ignition
Posts: 1635
Joined: Thu Nov 08, 2007 10:18 pm
Location: New Plymouth, NZ
Contact:

Re: Dreamer??

Postby Ignition » Tue Oct 20, 2009 10:05 pm

I have had thoughts of this as well over the years - and also a turboed CR500 based twin. :twisted:

Anyways...
I reckon a turbo would be better in a motard a you dont have to worry about an airbox as much and can shove the turbo in that space instead. Easiest would be one of the newer models that already has injection, so already has fuelpump setup etc. A number of them already have the ability to be reprogrammed, though to what degree I do not know. Also, I know Honda was having issues with response on the CRF250, it never ran as well as the carburetted version initially, feeling very flat. No idea how the release version goes. The 450's don't seem to have that issue with injection.

T Kilby
Posts: 6
Joined: Mon Sep 21, 2009 8:16 pm

Re: Dreamer??

Postby T Kilby » Tue Oct 20, 2009 10:42 pm

CR500 twin.... one word "scary" lol.

Yeah your right about a motard setup and i was think if i was to do it it would be to a EFI standard bike and i would start with a enduro or motard version as they already have a battery setup (12V needed for the Haltech). Im not sure of any other brands of ECU for bikes yet but i read Vortex have a piggy back ECU for some models, but don't think they offer a fully mapable one yet. It would chew up some money, but it doesn't stop me from dreaming.

T Kilby
Posts: 6
Joined: Mon Sep 21, 2009 8:16 pm

Re: Dreamer??

Postby T Kilby » Tue Oct 27, 2009 9:21 pm

Can anybody tell me if its posible to use the standard WR450 crank sensor? And other than MAP, coolant temp and TPS is there any other sensors that would have to be connected for an E6X to run a 450 bike with a single injector and LS1 coil setup?

T Kilby
Posts: 6
Joined: Mon Sep 21, 2009 8:16 pm

Re: Dreamer??

Postby T Kilby » Sun Nov 01, 2009 2:47 pm

ANYONE................

User avatar
Ignition
Posts: 1635
Joined: Thu Nov 08, 2007 10:18 pm
Location: New Plymouth, NZ
Contact:

Re: Dreamer??

Postby Ignition » Mon Nov 02, 2009 6:50 am

I would think a new trigger wheel with hall sensor would be the go.

T Kilby
Posts: 6
Joined: Mon Sep 21, 2009 8:16 pm

Re: Dreamer??

Postby T Kilby » Mon Nov 02, 2009 7:41 pm

How dificult do u reckon that would be to setup?

User avatar
Ignition
Posts: 1635
Joined: Thu Nov 08, 2007 10:18 pm
Location: New Plymouth, NZ
Contact:

Re: Dreamer??

Postby Ignition » Tue Nov 03, 2009 5:33 am

No more than on a car, except for the space issue. Cramming everything in might take a bit of head scratching to work out.

User avatar
Claudio
Posts: 1184
Joined: Wed Sep 26, 2007 10:44 am
Location: Santo Domingo, Dominican Republic
Contact:

Re: Dreamer??

Postby Claudio » Mon Jan 18, 2010 5:29 am

Hey guys, just caught this thread, with any haltech installation the main issue is triggering the haltech and then firing the motor the way its supposed to. Are these 2 stroke or 4? It may be possible, provided the right sensor combinations are used, and the engine can be fired how its meant to be fired.

My 2 cents.
Claudio
tuningtechnology@gmail.com
Independant Haltech Sales & Tech Support


Return to “Off-Topic”

Who is online

Users browsing this forum: No registered users and 2 guests