Search found 36 matches

by BlackBirdSR71
Tue May 21, 2019 12:36 pm
Forum: E11v2/E8
Topic: AEM Trigger disc settings.
Replies: 3
Views: 47

Re: AEM Trigger disc settings.

I wonder if 60 Trigger angle and Tooth Offset of 12 or 13 might work. I do not think I tried a combo above 10 Tooth Offset. 65 Trigger angle and 12 Tooth Offset might work??? I sure hope so.
by BlackBirdSR71
Tue May 21, 2019 12:29 pm
Forum: E11v2/E8
Topic: AEM Trigger disc settings.
Replies: 3
Views: 47

Re: AEM Trigger disc settings.

It is a 24 and 1. On these old ECU (and new ones too) it is the number of teeth seen for the full engine cycle (2x crank rotations for a 4-stroke). Make sure Trigger is connected to the 24x and Home connected to the 1x signals. Phase check your distributor. Engine on 20BTDC Cyl1. Rotor button shoul...
by BlackBirdSR71
Mon May 20, 2019 5:37 pm
Forum: E11v2/E8
Topic: AEM Trigger disc settings.
Replies: 3
Views: 47

AEM Trigger disc settings.

Well, with the help of Matt and others I have my old E11 running quite nicely on my 1978 Datsun 280Z. Learning how to dial in Raw Injection Timing, Dead Time compensations and a few other things. One problem still remains. I am using a 1983 Nissan Turbo Optical distributor. I can run this with the S...
by BlackBirdSR71
Mon May 20, 2019 4:50 pm
Forum: E11v2/E8
Topic: WB controller settings.
Replies: 4
Views: 43

Re: WB controller settings.

HaltechMatthew wrote:Somewhere around 100 for P, 30 to 50 for I, and zero for D. Sample around 50ms.


I'll give that a try. Thanks.
by BlackBirdSR71
Sun May 19, 2019 2:47 am
Forum: E11v2/E8
Topic: WB controller settings.
Replies: 4
Views: 43

Re: WB controller settings.

Default Map has these settings set to zero. That's the problems. I'm just looking for a rough Baseline figure to get started. Would just like something in the Ball Park to get me started and save some time.
by BlackBirdSR71
Sat May 11, 2019 2:24 am
Forum: E11v2/E8
Topic: WB controller settings.
Replies: 4
Views: 43

WB controller settings.

Using an AEM UEGO controller. 30-4100 on E11. What would good setting for PID be. And sample Rate. Here is a screenshot of my current settings. Any suggestions?

Halwin O2 control.jpg
by BlackBirdSR71
Tue Oct 16, 2018 4:48 am
Forum: E11v2/E8
Topic: E11 case ground?
Replies: 0
Views: 755

E11 case ground?

Just a really quick question. Is the E11 grounded to the outer case? I mounted direct to a floor pan with metal screws and I'm wondering if I may have to isolate the case. TIA.
by BlackBirdSR71
Wed Oct 10, 2018 12:32 am
Forum: E11v2/E8
Topic: e8 losing home signal on 60-2
Replies: 6
Views: 1067

Re: e8 losing home signal on 60-2

Take a high resolution picture of that Cam trigger wheel please. And post your Tune file. You can Zip the file and attach the Zip file as noted. Or use Drop Box, Google Drive or any of the other Cloud drives ( Your ISP usually has a Cloud file as well ) to upload you Tune File. Then simply post the ...
by BlackBirdSR71
Fri Oct 05, 2018 5:11 am
Forum: E11v2/E8
Topic: e8 losing home signal on 60-2
Replies: 6
Views: 1067

Re: e8 losing home signal on 60-2

Can you attach your tune to your Post? Also, do you have the correct Firing order setup? E8 ECU defaults to an inline firing order of 1-5-3-6-2-4 Honda J35 V6 firing order is 1-4-2-5-3-6 You have to use the " Auto Generate Firing Angles " button under Main Setup> Advanced Setup after chang...
by BlackBirdSR71
Mon Aug 13, 2018 8:19 am
Forum: E11v2/E8
Topic: Target AFR won't change.
Replies: 0
Views: 933

Target AFR won't change.

Having a weird problem with my E11 and HalWin 1.71. I can't seem to save changes to the Target AFR Map. Tried to change a number of cells from 14.7 to 15.0. Unlocked Variable Points. Made changes. Locked Variable Points and Saved all Maps under the Tune name. . However, when I reopen that particular...
by BlackBirdSR71
Mon Aug 13, 2018 7:59 am
Forum: E11v2/E8
Topic: Editing Aux Input parameters
Replies: 0
Views: 831

Editing Aux Input parameters

Question about Auxilary Input Parameters. A lot of the groups seem to have no Parameters set. There are no fields to adjust. All that you can select are Normal or Inverted. I want to set up an LSU Heater control or O2 Heater control on a WB controller, so that the Power Relay will not come on until ...
by BlackBirdSR71
Mon Feb 19, 2018 1:05 pm
Forum: E11v2/E8
Topic: E11v2 with msd dis 4 plus
Replies: 3
Views: 1883

Re: E11v2 with msd dis 4 plus

Ignition Output 1 through 6 goes to Cyl 1 through 6. Constant Charge, Rising 3.0ms. Yes. Found out the hard way on an Audi that the MSD DIS 4 ( and 4 Plus ) will not operate correctly with a Dwell rate of less than 2.5ms . 3.0ms should be ideal. 2.5ms dwell limit is not documented anywhere in MSD s...
by BlackBirdSR71
Mon Feb 19, 2018 1:01 pm
Forum: E11v2/E8
Topic: E11V2 Peugeot 205 New install
Replies: 3
Views: 1439

Re: E11V2 Peugeot 205 New install

Further to this, I don't really want to go wide band at this stage. Trying to keep it simple. You're also making it a lot harder on yourself. There is absolutely no reason at all not to use a WB controller these days. 14Point7, AEM X-seriers, PLX, Zeitronics are all good controllers. Stay away from...
by BlackBirdSR71
Tue Oct 03, 2017 5:09 pm
Forum: E11v2/E8
Topic: Inverting Map Axis
Replies: 1
Views: 1769

Inverting Map Axis

Using Halwin 1.71 on an E11. Is there any way to invert the MAP Axis. The Fuel and Spark RPM Axis on the Y axis start with 0 RPM at the top and high RPM at the bottom. I found this counter intuitive when building a Map. Can the Axis Values be inverted in the software, or even in the .INI configurati...
by BlackBirdSR71
Thu Jul 20, 2017 4:03 am
Forum: E11v2/E8
Topic: E8 with a 6 cylinder
Replies: 6
Views: 2874

Re: E8 with a 6 cylinder

Thanks. I think I've figured it out. Looks like the E8 can drive 8 Hi-z injectors or 4 Low-Z. ECU is actually a friends and he got it for free E8 is a whole lot better than what he has currently ( SDS ) . I'd rate SDS as pliers, the E8 as a trusty ol' Crescent wrench and a New Elite as a Snap-On Pro...

Go to advanced search