Search found 354 matches

by blakebonkofsky
Wed Jul 21, 2021 2:34 am
Forum: iC-7 Dash
Topic: IC7 inputs broadcast to Nexus?
Replies: 3
Views: 38

Re: IC7 inputs broadcast to Nexus?

Hi, Are any of the direct inputs on the IC7 broadcast to the Nexus over CAN, or is the dash basically receive-only, and cannot be used to gain additional inputs? I'm running low on inputs, and would like to route lower priority inputs to the dash, and read by the ECU via CAN, if possible. In genera...
by blakebonkofsky
Tue Jul 13, 2021 5:32 am
Forum: iC-7 Dash
Topic: steering wheel button input
Replies: 5
Views: 916

Re: steering wheel button input

Turbochook wrote:
Machinecult wrote:Keen as for this function


Same.

I'm keen to fit the tyre pressure set-up on my race car but want to be able to skip screens while driving. Bit hard when you can't reach with the harnesses on.



You can configure the analog inputs as buttons now :)

buttons.png
by blakebonkofsky
Thu Jul 01, 2021 4:17 am
Forum: Elite Series
Topic: my brushless thermofan wants a pwm+ signal, what do i do?
Replies: 4
Views: 111

Re: my brushless thermofan wants a pwm+ signal, what do i do?

Wouldn't assigning the thermofan as a Digital Duty Cycle work? The Elite outputs a pwm signal. I use this method to control a Ford Fusion fan controller for variable speed, soft start operation. Output frequency is 100 hz. The problem is that my fan requires a PWM+ signal and the Haltech is a PWM -...
by blakebonkofsky
Wed Jun 30, 2021 5:41 am
Forum: Elite Series
Topic: fuel cooler thermofan
Replies: 1
Views: 59

Re: fuel cooler thermofan

fastsaab wrote:Is there anyway to activate a thermofan for a fuel cooler with fuel temperature? I have a flex fuel sensor that shows me fuel temp but I don't see anyway to use that as a trigger.


Just set it up using a generic output, with the Fuel Temp as the conditional trigger.
by blakebonkofsky
Sat Jun 12, 2021 5:38 am
Forum: iC-7 Dash
Topic: iC7 odometer back to zero
Replies: 3
Views: 453

Re: iC7 odometer back to zero

Under the "System" section within the ICC software, you can set the Odometer to whatever you want. Just set it and send the configuration to the dash. In the future when you make changes, just load the current configuration from the dash, make your changes, and send it back. It should pres...
by blakebonkofsky
Tue Jun 08, 2021 10:11 am
Forum: iC-7 Dash
Topic: iC-7 Dash hardwire
Replies: 4
Views: 217

Re: iC-7 Dash hardwire

by blakebonkofsky
Wed Jun 02, 2021 2:46 am
Forum: Elite Series
Topic: Is there a professional wiring diagram for Elite Series
Replies: 2
Views: 303

Re: Is there a professional wiring diagram for Elite Series

If the diagram is designed for amateurs, why can't a professional figure it out?

Also, why isn't a professional designing their own wiring harness instead of using a premade harness?
by blakebonkofsky
Tue Jun 01, 2021 2:40 am
Forum: Nexus
Topic: Transmission control
Replies: 7
Views: 634

Re: Transmission control

Updated and worked Thanks Selected Drive input and assigned keypad button I assume that when Drive button is OFF it will be in neutral and when press ON it engage in 1st gear and up shift auto with rpm or what ever is selected and over rides with paddle shift button . Is that correct ? Were do Padd...
by blakebonkofsky
Mon May 31, 2021 7:22 am
Forum: Nexus
Topic: Transmission control
Replies: 7
Views: 634

Re: Transmission control

https://i.postimg.cc/65H0jgtF/Nexus-screen.png Can't sort out ,I'm I missing something ? You need to update your firmware. You're on 1.01, the Nexus is up to 1.07 now... NSP should have been auto-updating, but if not, click Help > Check For Updates. Then, create a new map. If you need, you can impo...
by blakebonkofsky
Sun May 30, 2021 5:28 am
Forum: Nexus
Topic: Transmission control
Replies: 7
Views: 634

Re: Transmission control

How do it engage to first gear , I noticed that it can be set to auto shift and a paddle switch overrides , I would like to use a switch button from neutral to 1st and vice versa from the CAN keypad is it possible ? You would need to set the "Selector Position Type" to One Input Per Posit...
by blakebonkofsky
Sat May 29, 2021 1:34 am
Forum: Nexus
Topic: Transmission control
Replies: 7
Views: 634

Re: Transmission control

Building a Drag 2jz Supra with clutchless 5 speed Liberty . Would like to know how Transmission control on liberty works and what ECU is capable to do I noticed that wiring is required for 5 solenoids for each gear , would like to know how and why Liberty control works great, we use it on our 7 spe...
by blakebonkofsky
Wed May 19, 2021 6:55 am
Forum: Elite Series
Topic: On the fly map switching?
Replies: 1
Views: 289

Re: On the fly map switching?

The CAN keypad is not compatible with the Elite ECUs, only the Nexus. Your dealer should have told you that.

That being said, you can definitely set up multiple options for tuning using rotary trim knobs or simple on/off switches if desired.
by blakebonkofsky
Sun May 16, 2021 5:08 am
Forum: iC-7 Dash
Topic: High beam indicator always on and turns off with stalk
Replies: 1
Views: 295

Re: High beam indicator always on and turns off with stalk

According to the wiring diagram included with the dash, the light indicator inputs need to be 12v switched, not ground.
by blakebonkofsky
Fri May 14, 2021 4:33 am
Forum: Elite Series
Topic: Elite 1500
Replies: 1
Views: 238

Re: Elite 1500

You could, in semi-sequential injection and wasted spark ignition.

Upgrading from a 1500 to a 2500 is just a matter of swapping the ECU and importing your current map. Wiring is identical besides the 2500 having 4 more ignition and injector outputs.
by blakebonkofsky
Fri May 14, 2021 4:30 am
Forum: Elite Series
Topic: is there any way to limit maximum injector pulsewidth?
Replies: 2
Views: 296

Re: is there any way to limit maximum injector pulsewidth?

Why would you want to do that?

Go to advanced search