Search found 12 matches

by Big Blue
Tue Sep 04, 2018 4:55 am
Forum: Elite Series
Topic: IAC not idling up
Replies: 9
Views: 569

Re: IAC not idling up

JimKden, Thank you for the reply. I wired up the #1 signal wire C28 to a switch/fused +12V source, and #2 control to A31 IAC Main Output. A31 is set to "low active state" and output I put as "both high and low". This settled the idle down without it pulsing the idle from 1000rpm ...
by Big Blue
Sun Sep 02, 2018 4:50 am
Forum: Elite Series
Topic: IAC not idling up
Replies: 9
Views: 569

Re: IAC not idling up

Just pinned out ground on the SRT-4 harness. C28 pins out to be chassis ground. That being said the Pulsed output from A31 should in theory control the IAC as normal but what setting/s do I set A31 at to correctly pass a high pulsed output to the IAC? Active State: HIgh? Low? Drive Type: High? Low? ...
by Big Blue
Sun Sep 02, 2018 1:38 am
Forum: Elite Series
Topic: IAC not idling up
Replies: 9
Views: 569

Re: IAC not idling up

.
by Big Blue
Sun Sep 02, 2018 1:36 am
Forum: Elite Series
Topic: IAC not idling up
Replies: 9
Views: 569

Re: IAC not idling up

.
by Big Blue
Sun Sep 02, 2018 1:32 am
Forum: Elite Series
Topic: IAC not idling up
Replies: 9
Views: 569

Re: IAC not idling up

.l
by Big Blue
Sun Sep 02, 2018 1:29 am
Forum: Elite Series
Topic: IAC not idling up
Replies: 9
Views: 569

Re: IAC not idling up

.
by Big Blue
Sun Sep 02, 2018 1:27 am
Forum: Elite Series
Topic: IAC not idling up
Replies: 9
Views: 569

Re: IAC not idling up

.
by Big Blue
Sun Sep 02, 2018 1:20 am
Forum: Elite Series
Topic: IAC not idling up
Replies: 9
Views: 569

Re: IAC not idling up

IAC motor.
by Big Blue
Sun Sep 02, 2018 1:16 am
Forum: Elite Series
Topic: IAC not idling up
Replies: 9
Views: 569

IAC not idling up

Hello Everyone, I'm running into issues with my IAC not idle up the car when the A/C Compressor kicks in. I have all the set ups attached to this post. The SRT-4 IAC wiring calls for: 1.) A IAC control input signal -pin #1 on IAC plug (C38) 2.) A return signal - pin #2 on IAC plug (C28) The Haltech ...
by Big Blue
Sun Aug 26, 2018 7:13 am
Forum: Elite Series
Topic: P1301 AT 4500 RPM
Replies: 3
Views: 597

P1301 AT 4500 RPM

Greetings Everyone, Does anyone have a clue why the code P1301 Trigger Reference Error will pop up on the back end of a pull? The car is running E85 and pulls pretty good up tell about 4500-4800 rpm. The car will pop out the exhaust and fall on it's face. Does this sound like a too retarded of timin...
by Big Blue
Sun Aug 26, 2018 6:53 am
Forum: Elite Series
Topic: A/C CONTROL FOR SRT4
Replies: 1
Views: 275

Re: A/C CONTROL FOR SRT4

Found the issue to be a leaking throttle body. The butterfly valve needed correcting as the IACV was completely shut and would never open until the A/C turned on. This allowed a drop in vacuum and excessive air to pass through the throttle body and IACV causing the car to stumble and kick off the A/...
by Big Blue
Mon Aug 20, 2018 4:08 am
Forum: Elite Series
Topic: A/C CONTROL FOR SRT4
Replies: 1
Views: 275

A/C CONTROL FOR SRT4

Greetings Everyone, While E85 tuning my 04' SRT4 on the Elite 1500 PnP I've run into a headache on the A/C compressor dropping way too much engine rpm when activated. It appears the car is not idling up on rpm when the A/C compressor signal is received. The output signal is sent but there is no phys...

Go to advanced search