Search found 9 matches

by rudye9mr
Sat Mar 16, 2019 5:34 am
Forum: Platinum Pro Plug-in
Topic: Evo ix PnP - water/meth integration
Replies: 7
Views: 1111

Re: Evo ix PnP - water/meth integration

Q:Will

HT-159976 WB1 – Single Channel CAN O2 Wideband Controller Kit



work with platinum pro plug in ecu???

A: Yes - please read the instructions - lol....i answered myself here : )
by rudye9mr
Tue Nov 20, 2018 10:49 pm
Forum: Elite Series
Topic: Aftermarket CAN wideband use?
Replies: 12
Views: 3409

Re: Aftermarket CAN wideband use?

hi...is this still the case - AEM can bus afr (or other can gauges e.g. oil pressure) cannot connect via can to Pro / Elite ECUs?
by rudye9mr
Wed Nov 14, 2018 10:41 am
Forum: Platinum Pro Plug-in
Topic: Evo ix PnP - water/meth integration
Replies: 7
Views: 1111

Re: Evo ix PnP - water/meth integration

20181113_193419~2.jpg
Aem wbo1 log


So i went through the log file to pc....seems the aem is connected and working fine.

I"ll need to figure out how to use the aem for o2 control rather than the narrowband...
by rudye9mr
Wed Nov 14, 2018 9:15 am
Forum: Platinum Pro Plug-in
Topic: Evo ix PnP - water/meth integration
Replies: 7
Views: 1111

Re: Evo ix PnP - water/meth integration

Got it to idle properly by deselecting the aem wideband that i have as avi2... used narrowband o2 input....


Will need to check
-voltage o/p from gauge that goes to avi2 for afr
-scaling afr vs voltage
by rudye9mr
Tue Nov 13, 2018 9:22 pm
Forum: Platinum Pro Plug-in
Topic: Evo ix PnP - water/meth integration
Replies: 7
Views: 1111

Re: Evo ix PnP - water/meth integration

https://youtu.be/KjORjaDqt1I

quick vid of first start up ---engine was cold.....shows afrs dipping as i think i have some erroneous settings....
by rudye9mr
Tue Nov 13, 2018 9:57 am
Forum: Platinum Pro Plug-in
Topic: Evo ix PnP - water/meth integration
Replies: 7
Views: 1111

Re: Evo ix PnP - water/meth integration

Finally swapped stock for the PnP... started it....started without any hesitation....then it went rich - afr gauge went from 14.8s to 10.0s.... lumpy idle.... i pulled up the target afr table and the cursor was on 14.7 (idling)....also got an error code....P0113:Intake air temperature sensor voltage...
by rudye9mr
Fri Oct 05, 2018 2:15 am
Forum: Platinum Pro Plug-in
Topic: Evo ix PnP - water/meth integration
Replies: 7
Views: 1111

Re: Evo ix PnP - water/meth integration

With respect to feeding a 0-5v Analogue signal from the water/meth gauge to the ECU for logging - i reckon i'll need an I/O box Yes you will need an IO box if you are using more than 2x AVI inputs (analogue voltages). You can leave the existing sensors in the Aux port, and I would actually recommend...
by rudye9mr
Tue Oct 02, 2018 12:03 am
Forum: Platinum Pro Plug-in
Topic: Evo ix PnP - water/meth integration
Replies: 7
Views: 1111

Re: Evo ix PnP - water/meth integration

Answering my own questions re:

Q:Can the AT1 (AT*) be used for as an analogue voltage input?
A: No - those inputs should be resistor based on the ECU side i.e. heat read by thermocouple as a resistance that is deciphered by the ecu i'm thinking...
by rudye9mr
Fri Sep 28, 2018 12:56 am
Forum: Platinum Pro Plug-in
Topic: Evo ix PnP - water/meth integration
Replies: 7
Views: 1111

Evo ix PnP - water/meth integration

Hi, New to the forum / Haltech world. ECU: Platinum pro Car: JDM MR IX I'm about to install and am also planning for later down with mods. Uego Wideband and Oil pressure will go to AVI1 and AVI2 . I'd eventually like to integrate an Aquamist set up with IDC / Boost / Knock as activators for the inje...

Go to advanced search